View NCP585LSN18T1G_1287867.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NCP585 Tri-Mode 300 mA CMOS LDO Regulator with Enable
The NCP585 series of low dropout regulators are designed for portable battery powered applications which require precise output voltage accuracy, low supply current, and high ripple rejection. These devices feature an enable function which lowers current consumption significantly and are offered in the SOT23-5 and the HSON-6 packages. This series of devices have three modes. Chip Enable (CE mode), Fast Transient Mode (FT mode), and Low Power Mode (LP mode). Both the FT and LP mode are utilized via the ECO pin.
Features http://onsemi.com MARKING DIAGRAM
5 1 DEV
M
* Low Dropout Voltage of 480 mV at 300 mA, Output Voltage = 1.0 V * * *
310 mV at 300 mA, Output Voltage = 1.5 V 230 mV at 300 mA, Output Voltage = 3.0 V Excellent Line and Load Regulation High Output Voltage Accuracy of 2% (3% LP mode) Ultra-Low Supply Current of: 3.5 mA (LP mode, Output Voltage < 1.6 V) 80 mA (FT mode, Output Voltage < 1.8 V) 60 mA (FT mode, Output Voltage 1.8 V) Excellent Power Supply Rejection Ratio of 65 dB Output Voltage Options: 0.9, 1.2 and 1.8 V Low Temperature Drift Coefficient on the Output Voltage Low Quiescent of 0.1 mA Fold Back Protection Circuit These are Pb-Free Devices
SOT23-5 SN SUFFIX CASE 1212
5 DEVM 1
= Specific Device Code = Date Code 6
6 1
HSON-6 SAN SUFFIX CASE 506AE 1
XXX XYY
* * * * * *
XXXX YY
= Specific Device Code = Wafer Lot
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 12 of this data sheet.
Typical Applications
* Portable Equipment * Hand-Held Instrumentation * Camcorders and Cameras
(c) Semiconductor Components Industries, LLC, 2005
1
March, 2005 - Rev. 3
Publication Order Number: NCP585/D
NCP585
ECO Vin Vout Vin ECO Vout
- + Vref Current Limit CE GND CE Vref
- +
Current Limit GND
Figure 1. Simplified Block Diagram for Active Low
Figure 2. Simplified Block Diagram for Active High
ECO
Vin
Vout
- + Vref Current Limit CE GND
Figure 1. Simplified Block Diagram for Active High with Auto Discharge
PIN FUNCTION DESCRIPTION
HSON-6 1 2 3 4 5 6 SOT23-5 1 - 5 4 2 3 Pin Name Vin NC Vout ECO GND CE or CE Power supply input voltage. No Connect. Regulated output voltage. Mode alternative pin. Power supply ground. Chip enable pin. Description
http://onsemi.com
2
NCP585
MAXIMUM RATINGS
Rating Input Voltage Input Voltage (CE or CE Pin) Input Voltage (ECO Pin) Output Voltage Output Current Power Dissipation Operating Junction Temperature Range Storage Temperature Range SOT23-5 HSON-6 Symbol Vin VCE VECO Vout Iout PD TJ Tstg Value 6.5 -0.3 to 6.5 -0.3 to 6.5 -0.3 to Vin +0.3 350 250 400 -40 to +85 +150 Unit V V V V mA mW C C
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected.
ELECTRICAL CHARACTERISTICS (Vin = Vout + 1.0 V, TA = 25C, unless otherwise noted.)
Characteristic Input Voltage Output Voltage (1.0 mA Iout 30 mA) VECO = Vin VECO = GND Line Regulation (Iout = 30 mA, Vout + 0.5 V Vin 6.0 V) FT Mode VECO = Vin LP Mode VECO = GND Load Regulation FT Mode (1.0 mA Iout 300 mA), VECO = Vin LP Mode (1.0 mA Iout 100 mA), VECO = GND Dropout Voltage (Iout = 300 mA) Vout = 0.9 V 1.0 Vout 1.4 V 1.5 Vout 2.5 V Power Supply Current (Iout = 0 mA) FT Mode, VECO = Vin Vout < 1.8 V Vout 1.8 V LP Mode, VECO = GND Vout < 1.6 V Vout 1.6 V Output Current (Vin - Vout = 1.0 V) Quiescent Current (VCE = Vin) Output Short Circuit Current (Vout = 0 V) Enable Input Threshold Voltage Active Low, ECO Input Voltage = High Active High, ECO Input Voltage = Low Output Noise Voltage (10 Hz - 100 kHz) N-Channel On Resistance for Auto Discharge Symbol Vin Vout Vout x 0.980 Vout x 0.970 Regline - - Regload - - VDO - - - Isupply - - - - Iout IQ Ilim Vthenl Vthenh Vn RLow 300 - - 1.0 1.0 - - 80 60 3.5 4.5 - 0.1 50 - - 30 60 111 90 8.0 9.0 - 1.0 - 0.6 Vin - - mVrms W mA mA mA V 40 15 ECO = H 0.55 0.48 0.31 ECO = L 0.59 0.51 0.32 70 30 ECO = H 0.78 0.70 0.45 ECO = L 0.80 0.75 0.48 V 0.01 0.05 0.15 0.20 mV - - Vout x 1.020 Vout x 1.030 %/V Min 1.4 Typ - Max 6.0 Unit V V
mA
http://onsemi.com
3
NCP585
TYPICAL CHARACTERISTICS
1.0 OUTPUT VOLTAGE, Vout (V) OUTPUT VOLTAGE, Vout (V) Vin = 2.8 V 0.8 1.0 Vin = 2.8 V 0.8
0.6
0.6
0.4 1.45 V 0.2 ECO = H 0.0 0 200 400 600 OUTPUT CURRENT, Iout (mA)
0.4 1.45 V 0.2 ECO = L 0.0 0 200 400 600 OUTPUT CURRENT, Iout (mA)
Figure 3. Output Voltage vs. Output Current
1.6 OUTPUT VOLTAGE, Vout (V) OUTPUT VOLTAGE, Vout (V) 1.4 1.2 1.0 0.8 1.8 V 0.6 0.4 0.2 0.0 0 200 400 ECO = H 600 Vin = 3.5 V 1.6 1.4 1.2 1.0 0.8
Figure 4. Output Voltage vs. Output Current
Vin = 3.5 V
1.8 V 0.6 0.4 0.2 0.0 0 200 400 ECO = L 600
OUTPUT CURRENT, Iout (mA)
OUTPUT CURRENT, Iout (mA)
Figure 5. Output Voltage vs. Output Current
1.0 0.9 OUTPUT VOLTAGE, Vout (V) 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0.0 1.0 2.0 3.0 4.0 Iout = 1.0 mA Iout = 30 mA Iout = 50 mA ECO = H 5.0 6.0 OUTPUT VOLTAGE, Vout (V) 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0.0
Figure 6. Output Voltage vs. Output Current
Iout = 1.0 mA Iout = 30 mA Iout = 50 mA ECO = L 1.0 2.0 3.0 4.0 5.0 6.0
INPUT VOLTAGE, Vin (V)
INPUT VOLTAGE, Vin (V)
Figure 7. Output Voltage vs. Input Voltage
Figure 8. Output Voltage vs. Input Voltage
http://onsemi.com
4
NCP585
TYPICAL CHARACTERISTICS
1.6 OUTPUT VOLTAGE, Vout (V) OUTPUT VOLTAGE, Vout (V) 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0 1.0 2.0 3.0 4.0 5.0 6.0 INPUT VOLTAGE, Vin (V) Iout = 1.0 mA Iout = 30 mA Iout = 50 mA ECO = H 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0 1.0 2.0 3.0 4.0 5.0 6.0 INPUT VOLTAGE, Vin (V) Iout = 1.0 mA Iout = 30 mA Iout = 50 mA ECO = L
Figure 9. Output Voltage vs. Input Voltage
Figure 10. Output Voltage vs. Input Voltage
100 SUPPLY CURRENT, Isupply (mA) SUPPLY CURRENT, Isupply (mA) 90 80 70 60 50 40 30 20 10 0 0 1.0 2.0 3.0 4.0 5.0 6.0 INPUT VOLTAGE, Vin (V) ECO = H
8 7 6 5 4 3 2 1 0 0 4.0 ECO = L
1.0
2.0
3.0
5.0
6.0
INPUT VOLTAGE, Vin (V)
Figure 11. Power Supply Current vs. Input Voltage
80 SUPPLY CURRENT, Isupply (mA) SUPPLY CURRENT, Isupply (mA) 70 60 50 40 30 20 10 ECO = H 0 0 1.0 2.0 3.0 4.0 5.0 6.0
Figure 12. Power Supply Current vs. Input Voltage
8 7 6 5 4 3 2 1 ECO = L 0 0 1.0 2.0 3.0 4.0 5.0 6.0
INPUT VOLTAGE, Vin (V)
INPUT VOLTAGE, Vin (V)
Figure 13. Power Supply Current vs. Input Voltage
Figure 14. Power Supply Current vs. Input Voltage
http://onsemi.com
5
NCP585
TYPICAL CHARACTERISTICS
0.83 OUTPUT VOLTAGE, Vout (V) 0.82 0.81 0.80 0.79 0.78 0.77 -50 Vout = 0.8 V ECO = H -25 0 25 50 75 100 OUTPUT VOLTAGE, Vout (V) 0.83 0.82 0.81 0.80 0.79 0.78 0.77 -50 Vout = 0.8 V ECO = L -25 0 25 50 75 100
TEMPERATURE (C)
TEMPERATURE (C)
Figure 15. Output Voltage vs. Temperature
1.53 OUTPUT VOLTAGE, VDO (V) OUTPUT VOLTAGE, VDO (V) 1.52 1.51 1.50 1.49 1.48 1.47 1.46 -50 Vout = 1.5 V ECO = H -25 0 25 50 75 100 1.53 1.52 1.51 1.50 1.49 1.48 1.47 1.46 -50
Figure 16. Output Voltage vs. Temperature
Vout = 1.5 V ECO = L -25 0 25 50 75 100
TEMPERATURE (C)
TEMPERATURE (C)
Figure 17. Output Voltage vs. Temperature
0.8 DROPOUT VOLTAGE, VDO (V) 0.7 0.6 85C 0.5 0.4 0.3 25C 0.2 0.1 0.0 0 50 100 150 200 Vout = 0.8 V ECO = H 250 300 40C DROPOUT VOLTAGE, VDO (V) 0.8 0.7
Figure 18. Output Voltage vs. Temperature
85C 0.6 0.5 0.4 40C 0.3 25C 0.2 0.1 0.0 0 50 100 150 200 Vout = 0.8 V ECO = L 250 300
OUTPUT CURRENT, Iout (mA)
OUTPUT CURRENT, Iout (mA)
Figure 19. Dropout Voltage vs. Output Current
Figure 20. Dropout Voltage vs. Output Current
http://onsemi.com
6
NCP585
TYPICAL CHARACTERISTICS
0.7 DROPOUT VOLTAGE, VDO (V) DROPOUT VOLTAGE, VDO (V) 0.6 0.5 0.4 0.3 40C 0.2 25C 0.1 0.0 0 Vout = 1.0 V ECO = H 50 100 150 200 250 300 85C 0.7 0.6 0.5 85C 0.4 0.3 40C 0.2 0.1 0.0 0 25C Vout = 1.0 V ECO = L 150 200 250 300
50
100
OUTPUT CURRENT, Iout (mA)
OUTPUT CURRENT, Iout (mA)
Figure 21. Dropout Voltage vs. Output Current
0.40 DROPOUT VOLTAGE, VDO (V) DROPOUT VOLTAGE, VDO (V) 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0.00 0 200 25C Vout = 1.5 V ECO = H 50 100 150 250 300 85C 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05
Figure 22. Dropout Voltage vs. Output Current
85C
40C
40C
25 (C)
Vout = 1.5 V ECO = L 200 250 300
0.00 0
50
100
150
OUTPUT CURRENT, Iout (mA)
OUTPUT CURRENT, Iout (mA)
Figure 23. Dropout Voltage vs. Output Current
100 RIPPLE REJECTION, RR (dB) RIPPLE REJECTION, RR (dB) 90 I = 30 mA out 80 70 60 50 40 30 20 10 0 0 Vout = 0.8 V Vin = 1.8 V + 0.2 Vp-p Cout = 2.2 mF, ECO = H 1 10 100 Iout = 50 mA Iout = 1.0 mA 100 90 80 70 60 50 40 30 20 10 0 0
Figure 24. Dropout Voltage vs. Output Current
Vout = 0.8 V Vin = 1.8 V + 0.2 Vp-p Cout = 2.2 mF, ECO = L
Iout = 1.0 mA
Iout = 30 mA
Iout = 50 mA 1 10 100
FREQUENCY, f (kHz)
FREQUENCY, f (kHz)
Figure 25. Ripple Rejection vs. Frequency
Figure 26. Ripple Rejection vs. Frequency
http://onsemi.com
7
NCP585
TYPICAL CHARACTERISTICS
100 RIPPLE REJECTION, RR (dB) 90 80 70 60 50 40 30 20 10 0 0 Vout = 1.5 V Vin = 2.5 V + 0.2 Vp-p Cout = 2.2 mF, ECO = H 1 10 100 Iout = 50 mA Iout = 1.0 mA RIPPLE REJECTION, RR (dB) Iout = 30 mA 100 90 80 70 60 50 40 30 20 10 0 0 1 10 Iout = 50 mA 100 Iout = 1.0 mA Iout = 30 mA Vout = 1.5 V Vin = 2.5 V + 0.2 Vp-p Cout = 2.2 mF, ECO = L
FREQUENCY, f (kHz)
FREQUENCY, f (kHz)
Figure 27. Ripple Rejection vs. Frequency
Figure 28. Ripple Rejection vs. Frequency
0.88 Input Voltage OUTPUT VOLTAGE, Vout (V) 0.86 0.84 0.82 Output Voltage 0.80 0.78 0.76 0 ECO = H, Iout = 30 mA Cout = Tantalum 1.0 mF Vout = 0.8 V 10 20 30 40 50 60 70 80 90
4 3 2 1 0 -1 -2 100 OUTPUT VOLTAGE, Vout (V)
3.0 Input Voltage INPUT VOLTAGE, Vin (V) 2.5 2.0 1.5 1.0 0.5 0 0.0 Output Voltage
4 3 2 1 0
0.4
0.8
1.2
ECO = L, Iout = 30 mA -1 Cout = Tantalum 1.0 mF Vout = 0.8 V -2 1.6 2.0 2.4 2.8 3.2 3.6 4.0 TIME, t (ms)
TIME, t (ms)
2.68 OUTPUT VOLTAGE, Vout (V) 2.66 2.64 2.62 Output Voltage 2.60 2.58 2.56 0 ECO = H, Iout = 30 mA Cout = Ceramic 1.0 mF Vout = 2.6 V 10 20 30 40 50 60 70 80 90 Input Voltage
5 4 3 2 1 0 -1 100 OUTPUT VOLTAGE, Vout (V)
5.0 4.5 4.0 3.5 3.0 Output Voltage 2.5 2.0 0.0 0.4 ECO = L, Iout = 30 mA Cout = Ceramic 1.0 mF Vout = 2.6 V Input Voltage
5 4 3 2 1 0 -1 4.0
INPUT VOLTAGE, Vin (V)
0.8
1.2
1.6 2.0
2.4
2.8
3.2
3.6
TIME, t (ms)
TIME, t (ms)
Figure 29. Input Transient Response
http://onsemi.com
8
INPUT VOLTAGE, Vin (V)
INPUT VOLTAGE, Vin (V)
NCP585
TYPICAL CHARACTERISTICS
1.2 OUTPUT VOLTAGE, Vout (V) 1.1 Load Current 50 ECO = H, Vin = 1.8 V Cin = Tantalum 1.0 mF Cout = Tantalum 1.0 mF Vout = 0.8 V Output Voltage -100 -150 40 0 -50 1.0 0.9 0.8 0.7 0.6 0 150 100 1.2 OUTPUT CURRENT, Iout (mA) OUTPUT VOLTAGE, Vout (V) 1.1 Load Current 0 ECO = H, Vin = 1.8 V Cin = Tantalum 1.0 mF Cout = Tantalum 1.0 mF Vout = 0.8 V Output Voltage -90 -30 -60 1.0 0.9 0.8 0.7 0.6 0 60 30 OUTPUT CURRENT, Iout (mA) OUTPUT CURRENT, Iout (mA) OUTPUT CURRENT, Iout (mA)
-120 5 10 15 20 25 30 35 40 Time, t (ms)
5
10
15
20 Time, t (ms)
25
30
35
1.2 OUTPUT VOLTAGE, Vout (V) 1.1 Load Current 1.0 0.9 0.8 Output Voltage 0.7 0.6 0 ECO = H, Vin = 1.8 V Cin = Tantalum 1.0 mF Cout = Tantalum 2.2 mF Vout = 0.8 V
60 30 0 -30 -60 -90
3.0 OUTPUT CURRENT, Iout (mA) OUTPUT VOLTAGE, Vout (V) 2.5 Load Current
20 10 0 ECO = H, Vin = 1.8 V Cin = Tantalum 1.0 mF Cout = Tantalum 1.0 mF Vout = 0.8 V Output Voltage -10 -20 -30 -40 4.0
2.0 1.5 1.0 0.5 0 0
5
10
15
20 Time, t (ms)
25
30
35
-120 40
0.5
1.0
1.5
2.0
2.5
3.0
3.5
Time, t (ms)
3.0 OUTPUT VOLTAGE, Vout (V) 2.9 Load Current 2.8 2.7 2.6 2.5 2.4 0 Output Voltage ECO = H, Vin = 3.6 V Cin = Ceramic 1.0 mF Cout = Ceramic 1.0 mF Vout = 2.6 V
60 30 0 -30 -60 -90
4.5 OUTPUT CURRENT, Iout (mA) OUTPUT VOLTAGE, Vout (V) 4.0 Load Current 3.5 3.0 2.5 2.0 1.5 0
20 10 0 -10 -20 ECO = L, Vin = 3.6 V Cin = Ceramic 1.0 mF Cout = Ceramic 1.0 mF Vout = 2.6 V 2.0 2.5 3.0 3.5 -30 -40 4.0
Output Voltage
5
10
15
20 Time, t (ms)
25
30
35
-120 40
0.5
1.0
1.5
Time, t (ms)
Figure 30. Load Transient Response
http://onsemi.com
9
NCP585
TYPICAL CHARACTERISTICS
3.0 OUTPUT VOLTAGE, Vout (V) 2.9 Load Current 2.8 2.7 2.6 2.5 2.4 0 ECO = H, Vin = 1.8 V Cin = Ceramic 1.0 mF Cout = Ceramic 2.2 mF Vout = 2.6 V Output Voltage -90 0 -30 -60 60 30 4.5 OUTPUT CURRENT, Iout (mA) OUTPUT VOLTAGE, Vout (V) 4.0 Load Current ECO = L, Vin = 3.6 V Cin = Ceramic 1.0 mF Cout = Ceramic 2.2 mF Vout = 2.6 V Output Voltage -30 -40 4.0 0 -10 -20 3.5 3.0 2.5 2.0 1.5 0 20 10 OUTPUT CURRENT, Iout (mA) OUTPUT VOLTAGE, Vout (V) OUTPUT VOLTAGE, Vout (V)
5
10
15
20 Time, t (ms)
25
30
35
-120 40
0.5
1.0
1.5
2.0
2.5
3.0
3.5
Time, t (ms)
Figure 30. (continued) Load Transient Response
2.7 CE INPUT VOLTAGE, VCE (V) 1.8 VCE = 0 V 1.8 V 0.9 0 ECO = H Vin = 1.8 V Cin = Tantalum 1.0 mF Cout = Tantalum 1.0 mF Iout = 300 mA 0 10 20 30 40 50 60
2.5 2.0 1.5 1.0 0.5 0 OUTPUT VOLTAGE, Vout (V) CE INPUT VOLTAGE, VCE (V)
2.7 1.8 VCE = 0 V 1.8 V 0.9 0 ECO = L Vin = 1.8 V Cin = Tantalum 1.0 mF Cout = Tantalum 1.0 mF Iout = 300 mA 0 0.1 0.2 0.3 0.4 0.5 0.6
2.5 2.0 1.5 1.0 0.5 0
-0.9 -1.8 -2.7 -30 -20 -10
-0.9 -1.8 -2.7 -0.3 -0.2 -.01
-0.5 70
-0.5 0.7
TIME, t (ms)
TIME, t (ms)
6.0 CE INPUT VOLTAGE, VCE (V) 4.0 2.0 0 VCE = 0 V 4.3 V
7.0 OUTPUT VOLTAGE, Vout (V) CE INPUT VOLTAGE, VCE (V) 6.0 5.0 4.0 3.0 ECO = H Vin = 4.3 V Cin = Ceramic 1.0 mF Cout = Ceramic 1.0 mF Iout = 300 mA 0 20 40 60 80 2.0 1.0 0
6.0 4.0 2.0 0 VCE = 0 V 4.3 V
7.0 6.0 5.0 4.0 3.0 ECO = L Vin = 4.3 V Cin = Ceramic 1.0 mF Cout = Ceramic 1.0 mF Iout = 300 mA 0 0.1 0.2 0.3 0.4 0.5 0.6 2.0 1.0 0
-2.0 -4.0 -6.0 -8.0 -10 -60 -40 -20
-2.0 -4.0 -6.0 -8.0 -10 -0.3 -0.2 -0.1
-1 100 120 140
-1.0 0.7
TIME, t (ms)
TIME, t (ms)
Figure 31. Turn-On Speed with CE Pin, Vout = 0.8 V
http://onsemi.com
10
NCP585
TYPICAL CHARACTERISTICS
Vin = 1.8 V, Cin = Tantalum 1.0 mF, Cout = Tantalum 1.0 mF, Vout = 0.8 V
3.0 VECO = 0 V to 1.4 V 2.0 1.0 0.0 OUTPUT VOLTAGE, Vout (V) 0.81 0.80 0.79 0.81 0.80 0.79 0.81 0.80 0.79 0.81 0.80 0.79 0.81 0.80 0.79 0.81 0.8 0.79 0.78 -0.2 ECO INPUT VOLTAGE, VECO (V) 1.6 1.8 3.0 2.0 1.0 0.0 OUTPUT VOLTAGE, Vout (V) 1.01 1.00 0.99 1.01 1.00 0.99 1.01 1.00 0.99 1.01 1.00 0.99 1.01 1.00 0.99 1.01 1.00 0.99 0.98 0.0 ECO INPUT VOLTAGE, VECO (V) 2.0 Iout = 300 mA Iout = 1 mA
Iout = 10 mA
Iout = 50 mA
Iout = 100 mA Iout = 200 mA
Iout = 300 mA
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
TIME, t (ms)
Vin = 2.0 V, Cin = Ceramic 1.0 mF, Cout = Ceramic 1.0 mF, Vout = 1.0 V
VECO-0 V to 2.0 V
Iout = 1 mA
Iout = 10 mA
Iout = 50 mA
Iout = 100 mA
Iout = 200 mA
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
TIME, t (ms)
Figure 32. Output Voltage at Mode Alternative Point http://onsemi.com
11
NCP585
APPLICATION INFORMATION
Input Decoupling Output Decoupling
A 1.0 mF ceramic capacitor is the recommended value to be connected between Vin and GND. For PCB layout considerations, the traces on Vin and GND should be sufficiently wide in order to minimize noise and prevent unstable operation.
It is best to use a 1.0 mF capacitor value on the Vout pin. For better performance, select a capacitor with low Equivalent Series Resistance (ESR). For PCB layout considerations, place the output capacitor close to the output pin and keep the leads short as possible.
ORDERING INFORMATION
Device NCP585DSAN09T1G NCP585DSAN12T1G NCP585DSAN18T1G NCP585DSN09T1G NCP585DSN12T1G NCP585DSN18T1G NCP585HSAN09T1G NCP585HSAN12T1G NCP585HSAN18T1G NCP585HSN09T1G NCP585HSN12T1G NCP585HSN18T1G NCP585LSAN09T1G NCP585LSAN12T1G NCP585LSAN18T1G NCP585LSN09T1G NCP585LSN12T1G NCP585LSN18T1G Output Type / Features Active High w/Auto Discharge, LP and FT Mode Active High w/Auto Discharge, LP and FT Mode Active High w/Auto Discharge, LP and FT Mode Active High w/Auto Discharge, LP and FT Mode Active High w/Auto Discharge, LP and FT Mode Active High w/Auto Discharge, LP and FT Mode Active High, LP and FT Mode Active High, LP and FT Mode Active High, LP and FT Mode Active High, LP and FT Mode Active High, LP and FT Mode Active High, LP and FT Mode Active Low, LP and FT Mode Active Low, LP and FT Mode Active Low, LP and FT Mode Active Low, LP and FT Mode Active Low, LP and FT Mode Active Low, LP and FT Mode Nominal Output Voltage 0.9 1.2 1.8 0.9 1.2 1.8 0.9 1.2 1.8 0.9 1.2 1.8 0.9 1.2 1.8 0.9 1.2 1.8 Marking B09D B12D B18D R09 R12 R18 B09B B12B B18B Q09 Q12 Q18 B09A B12A B18A P09 P12 P18 Package HSON-6 (Pb-Free) HSON-6 (Pb-Free) HSON-6 (Pb-Free) SOT23-5 (Pb-Free) SOT23-5 (Pb-Free) SOT23-5 (Pb-Free) HSON-6 (Pb-Free) HSON-6 (Pb-Free) HSON-6 (Pb-Free) SOT23-5 (Pb-Free) SOT23-5 (Pb-Free) SOT23-5 (Pb-Free) HSON-6 (Pb-Free) HSON-6 (Pb-Free) HSON-6 (Pb-Free) SOT23-5 (Pb-Free) SOT23-5 (Pb-Free) SOT23-5 (Pb-Free) Shipping 3000 Tape & Reel 3000 Tape & Reel 3000 Tape & Reel 3000 Tape & Reel 3000 Tape & Reel 3000 Tape & Reel 3000 Tape & Reel 3000 Tape & Reel 3000 Tape & Reel 3000 Tape & Reel 3000 Tape & Reel 3000 Tape & Reel 3000 Tape & Reel 3000 Tape & Reel 3000 Tape & Reel 3000 Tape & Reel 3000 Tape & Reel 3000 Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D.
http://onsemi.com
12
NCP585
PACKAGE DIMENSIONS
HSON-6 SAN SUFFIX CASE 506AE-01 ISSUE A
D
PIN ONE REFERENCE 2X 6 4
A
B
E1 0.20 C
2X 1 3
E
0.20 C TOP VIEW 0.10 C A
6X
NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.10 AND 0.15 MM FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. MILLIMETERS MIN MAX 0.70 0.90 0.15 REF 0.20 0.40 2.90 BSC 1.40 1.60 3.00 BSC 2.80 BSC 1.50 1.70 0.95 BSC 0.15 0.25
0.08 C
SEATING PLANE
(A3) SIDE VIEW
C
DIM A A3 b D D2 E E1 E2 e L
D2 e
1 3
L
6X
E2
6 4
EXPOSED PAD
b BOTTOM VIEW
6X
NOTE 3
0.10 C A B 0.05 C
http://onsemi.com
13
NCP585
PACKAGE DIMENSIONS
SOT23-5 SN SUFFIX CASE 1212-01 ISSUE O
NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DATUM C IS A SEATING PLANE. DIM A1 A2 B C D E E1 e e1 L L1 MILLIMETERS MIN MAX 0.00 0.10 1.00 1.30 0.30 0.50 0.10 0.25 2.80 3.00 2.50 3.10 1.50 1.80 0.95 BSC 1.90 BSC 0.20 --- 0.45 0.75
A
5 1
D
4 2 3
B
A2 0.05 S
A1 L
E
E1 L1 e e1 B
5X
C
M
0.10
CB
S
A
S
C
SOLDERING FOOTPRINT*
1.9 0.074
0.95 0.037
2.4 0.094 1.0 0.039 0.7 0.028
SCALE 10:1
mm inches
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: N. American Technical Support: 800-282-9855 Toll Free Literature Distribution Center for ON Semiconductor USA/Canada P.O. Box 61312, Phoenix, Arizona 85082-1312 USA Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada Phone: 81-3-5773-3850 Email: orderlit@onsemi.com ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative.
http://onsemi.com
14
NCP585/D

▲Up To Search▲

Price & Availability of NCP585LSN18T1G

	To Download NCP585LSN18T1G Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .